Align post — with tunnel attached — to center of I-Clip and press firmly. Slide open top panel to reveal channel and align to wiper arm. Secure blade by sliding panel closed once inserted. Press firmly to secure. Skip to content Just added to your cart. Continue shopping. How to Change Windshield Wipers — The Clix Wipers Way Learn how to replace your windshield wipers, and how Clix Wipers simplifies the old method of changing wipers with a simple one-click system.
Helena St. Part 2. Release the wiper blade. Locate the small tab on the underside of wiper blade near where the rubber insert meets the metal arm , then push it in or in some cases, pull on it to release. Pull down on the blade and it should then slide off the hook of the metal arm. Sometimes it helps to push the wiper up into the holder, press the tab, and then remove.
The bare metal arms are now exposed, and, if left in the standing position, they can snap back and damage your windshield. To be extra safe, place a rag or cloth underneath the metal arm while it rests on the windshield. Take out the new wiper. If the left and right wipers are different sizes, be sure to match the new wiper to the correct side.
Push the movable hinge on the new blade until the hinge is perpendicular to the rest of the blade. Line the new blade up with the metal arm so that the metal hook will go through the hole in the blade. Push the metal hook through the hole in the blade. The metal hook should push up against the rubber insert. Pull up on the blade until you hear as well as feel it click it into place.
Gently push the blade back down to a resting position against the windshield. Repeat with the other wiper blade. Check the wiper arm angle. If the wiper arm angle is off it can cause chattering. The rule of thumb is that the blade is 90 degrees to the glass mid-swipe The reason for mid-swipe is it will change angle from the top of the windshield to the bottom of the windshield due to the curvature of the glass.
Turn on the ignition and wet the windshield with wiper fluid to test the new wipers for proper installation. If the new wipers are streaky, first try cleaning the rubber insert with alcohol wipes or a cloth soaked in mineral spirits. If the wipers are still streaky, check that the blades are properly installed. If all else fails, stop by your local auto-parts store for help. Part 3. Begin by locating the pads at end of the blade; the pads should have small tabs sticking out.
Push in the tabs and pull up on the blade to slip it off the assembly. If you find pushing the tabs in to be difficult, you can use a pair of needle-nose pliers to help you.
On some models, the wiper arm must be removed so that the rubber insert can be replaced correctly. Slide the rubber insert off of the wiper arm. Once the tabs are past the blade clamp near the center of the blade , release the tabs and pull the rubber insert completely free of the arm. The blade is now exposed, and, if left in the standing position, it can snap back and damage your windshield. To be extra safe, place a rag or cloth underneath the blade while it rests against the windshield.
Take out the new rubber insert. If the left and right wipers are different sizes, be sure to match the new insert to the correct blade. Slide the new rubber insert onto the blade, starting at the same end you just pulled the old one away from. When the insert is in place, be sure the clamps on the blade are securely holding it in place.
Verify that the far pad is secured in place by the last clamp. Gently push the blade back down to a resting position against the windshield and then repeat with the other rubber insert. Hovig Manouchekian. No, wiper blades vary quite a bit between vehicles in terms of design. Some of the newer wiper blades are a lot more elaborate. It's important to follow the manufacturer's instructions on how to replace them on your vehicle.
Not Helpful 0 Helpful 1. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube. Stopping them in this position can make changing the blades a bit easier. Helpful 2 Not Helpful 0. Helpful 2 Not Helpful 3. Most auto-supply stores will replace your wipers for free when you buy new blades from them.
Helpful 0 Not Helpful 0. Run an alcohol pad or a rag dipped in mineral spirits along the rubber of the blade to clean and make the rubber wear longer.
Helpful 0 Not Helpful 1. You Might Also Like How to. How to. About This Article.
0コメント